The brake pump is located inside the engine compartment and near the brake pedal. The brake booster plays an important role in performing the braking process as well as completing this process

The main function of the brake pump is to help brake properly and comfortably to stop the car

When the driver brakes to stop or slow down the car, he applies pressure to the brake pedal and this pressure is first applied to the brake pump

When the initial pressure is applied to the brake pump, the oil inside it is sent to the wheels through a special pipe and duct for braking

The pump and brake tank are located in the engine compartment and near the brake pedal on the brake booster

The brake booster plays an important role in performing the braking process as well as completing this process. Symptoms of damage to this part include oil leakage, brake pedal softening and loss of braking power

After replacing this part, you need to make sure that it works properly and that there are no leaks around it

It is recommended to check the amount of oil in the brake pump after replacing this part and to maintain safety issues

Proper operation of the brake pump increases the durability and useful life of the brake pad

In fact, in general, it can be said that the brake pump is responsible for maintaining the brake fluid after the driver depresses the brake pedal towards the wheels. The brake fluid reservoir is located on the brake pump, which is called the brake source. The brake pump sends the oil to the wheels by pressing the wheels according to the accessories it has inside, after the pedal presses the pedal and presses the booster that enters this tank, causing the brakes to catch. In cars with ABS, the oil goes to the ABS after being sent from the brake pump and from there it is divided into four wheels. But if the car does not have ABS, the oil is connected to a three-way inside the pump, which is three Rahi is responsible for dividing the oil between 4 wheels. The brake pump is usually two-circuit. One part for the front wheels and one part for the rear wheels. In the EBS system, this circuit is a cross that has a load tube on the right front wheel and a left rear wheel, and vice versa

This is the brake pump that is responsible for maintaining the brake fluid and warns of the danger of the brake. Because most brake pumps have a sensor that warns the driver if there is no oil or oil is low. This warning is very important for the driver because after the brake fluid level drops, he should check why the brake fluid has decreased. The important point in the brake system is that the brake fluid should not decrease in any way. Leakage of brake fluid has two reasons or it has leaked somewhere in the pipe hose and brake cylinder

Or the amount of pads has decreased and the level of this brake fluid has dropped

The driver should be careful that after seeing or seeing the warning of low brake oil, be sure to refer to a specialized brake repair shop to find the reason for low brake oil. Let’s be. We need to see why the brake fluid is running low and fix it. Brake fluid in the pump has two degrees, max and mine, which must be adjusted for better performance. We must note that the brake system does not use oil at all. The oil must exist to some extent and if it is low, it must have a good reason

One of the signs and symptoms of a brake pump failure is that the brake pedal acts like a clutch. In this case, the pedal is not stiff underfoot. This is called emptying the brake, which is one of the signs and symptoms of failure of the brake pump of passenger cars. This emptying the pedal will damage the car’s brake pump. Because the parts and accessories that are inside it are rubber and cause the oil not to reach the wheels, and in this case, the oil pressure escapes from the parts.

One of the signs and symptoms of a car brake pump failure is that before the pedal is fully depressed, the driver feels that the pedal is slowly emptying downhill and in slow stops under the pedal.

In this case, the damage is still low. If you go to the repair shop in these conditions, the brake pedal will not empty completely. Otherwise, the equipment will deteriorate over time and the tires will not hold the oil and the pedal will be completely empty.

One of the reasons for the failure of the car brake pump is the delay in changing the brake fluid in the brake pump tank. After 1 year, the brake fluid inside the car brake pump must be replaced, because the brake fluid becomes humid and has a boiling temperature, and due to cold and heat, it loses its properties. The best way to change the brake fluid is to open the tank. Brake and wash it with water and rica.

Water dissolves and dissolves the brake fluid. After cleaning the tank by water and rica, we must pour the clean brake oil into the brake pump and vent the wheels and the path of the brake system individually until the previous oil enters the drain brake system. If the oil is not changed, it will damage the brake pump and the ABS block.

In short, if you see the following symptoms, your car’s brake pump is defective

The brake pedal acts like a clutch. (Releasing the brake)

The pedal is released and loosened on slopes and gentle stops under the pedal

When braking, the car is pulled on one side